Model No.: 3001015/20-106
Applicable models: JNine pingchai, five tons of king
3001015 is the left knuckle; 3001020 is the right knuckle
Working principle and function
The function of kingpin inclination angle is to make the wheels return to normal automatically. Generally, the wheel axis is not on the horizontal plane. For convenience, it is assumed that the wheel axis is on the horizontal plane when driving in a straight line. For the case where the wheel axis is not in the horizontal plane, just change the horizontal plane in the figure below into a conical surface. As shown in the figure below, considering the lines on the horizontal plane that intersect with the kingpin, the included angle between the kingpin and these lines has a maximum value. When the car runs in a straight line, the intersection angle between the wheel axis and the kingpin is exactly this maximum. The included angle between the wheel axis and the kingpin is constant during steering. When the wheel turns an angle, the wheel axis tilts downward away from the horizontal plane, resulting in the body lifting and the potential energy increasing. In this way, the gravity of the car itself has the effect of returning the steering wheel to the original middle position. When the vehicle is parked horizontally, in the transverse vertical plane of the vehicle, the included angle between the kingpin axis and the ground vertical line is the inclination angle of the kingpin.
Front wheel camber:
If the wheel is installed just perpendicular to the road when the vehicle is empty, the wheel inclination may occur due to load-bearing deformation of the axle when the vehicle is fully loaded, which will accelerate the wear of vehicle tires. In addition, the vertical reaction force of the road surface to the wheel along the axial component of the hub will make the hub press the small bearing at the outer end, increase the load of the small bearing at the outer end and the fastening nut of the hub, and reduce their service life. Therefore, there is a camber angle for the front wheels. However, the camber angle should not be too large, otherwise the tire will be biased and worn. As shown in the left figure, when the vehicle is parked horizontally, the included angle between the wheel plane and the vertical line on the ground in the transverse vertical plane of the vehicle is the camber angle of the front wheel.
Front toe in:
When the wheel has camber, it is similar to a rolling cone when rolling, resulting in the wheels on both sides rolling outward. Due to the restraint of the tie rod and axle, the wheel will not roll outward, and the wheel will roll inward on the ground, thus increasing the wear of the tire. In order to avoid the adverse consequences caused by conical rolling effect, the two front wheels are properly deflected inward, that is, the front wheel toe in is formed.
In order that you can buy the parts suitable for your original car ai soon as possible, please prepare the following documents before consulting the parts.if the parts number can be seen on the original parts,please try to provide the information you can see,such as the part number beginning with,A2 or YG;
If the part number can not be found on the original,please provide the vehicle identification number (commonly known as:frame number,chassis number)on the vehicle license,usually on the frame on both sides of the engine or on the plate of the passenger’s car that begins with “LZZ”and the following 8 letters and numbers:For accessories that you do not know about,it is suggested to take clear photos with your phone or camera light and send them to customer service.
Please provide the real photo of the original car,and do not send the screenshot of the picture searched online to the customer service.The buyer shall bear all the responsibility for the wrong judgment of the accessory model caused by this.
Jilin Province Xuan Yi Trading Co.,Ltd.
- Company Name: Jilin Province Xuan Yi Trading Co.,Ltd.
- Representative: Jin Du
- Product/Service: Steering knuckle , Steering knuckle arm , Front axle , Sun gear , Drive shaft series , Differential mechanism
- Capital (Million US $): 1,000,000RMB
- Year Established: 2021
- Total Annual Sales Volume (Million US $): Below US$1 Million
- Export Percentage: 61% - 70%
- Total Annual Purchase Volume (Million US $): Below US$1 Million
- No. of Production Lines: 3
- No. of R&D Staff: 5 -10 People
- No. of QC Staff: Fewer than 5 People
- Factory Size (Sq.meters): 3,000-5,000 square meters
- Factory Location: Changchun Automobile Industry Development Zone, Jilin Province
- Contact Person: Ms. xinran
- Tel: 86-17743468165
Premium Related Products